tag:blogger.com,1999:blog-6100511197805579796.post88767036999033387..comments2024-02-14T18:43:36.096+01:00Comments on Davide Gironi blog: Drive a stepper motor with acceleration and deceleration using an Allegro driver on ATmega8Davide Gironihttp://www.blogger.com/profile/16366076989473118278noreply@blogger.comBlogger14125tag:blogger.com,1999:blog-6100511197805579796.post-37369553234290662682022-09-04T11:28:23.652+02:002022-09-04T11:28:23.652+02:00Hello and thank you for this feedback. Take a look...Hello and thank you for this feedback. Take a look at the astepper.h file. You will find two parameters (ASTEPPER_STEPLIMITMIN and ASTEPPER_STEPLIMITMAX) that "defines how fast and/or slow will your motor spin". Hope this helps.Davide Gironihttps://www.blogger.com/profile/16366076989473118278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-30903596323467641872022-09-03T22:10:33.107+02:002022-09-03T22:10:33.107+02:00Thanks for the article) Can you please tell me how...Thanks for the article) Can you please tell me how can I change acceleration slope angle using approximation formula? Tolik4https://www.blogger.com/profile/11126057615146691571noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-61733462401419636372019-06-28T13:29:17.019+02:002019-06-28T13:29:17.019+02:00Hello, you can find the formula for the CO in the ...Hello, you can find the formula for the CO in the blogpostDavide Gironihttps://www.blogger.com/profile/16366076989473118278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-22740615038822409582018-12-09T23:14:57.618+01:002018-12-09T23:14:57.618+01:00This comment has been removed by the author.Anonymoushttps://www.blogger.com/profile/10678256200857803630noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-14305005884314659572018-11-23T12:09:51.131+01:002018-11-23T12:09:51.131+01:00Hi. How to calculate initial C0 value. Hi. How to calculate initial C0 value. Jarnsaxarhttps://www.blogger.com/profile/01261162927792740180noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-46803450772074178022018-04-06T12:04:04.716+02:002018-04-06T12:04:04.716+02:00Hello, unluckly I do not measure it.Hello, unluckly I do not measure it.Davide Gironihttps://www.blogger.com/profile/16366076989473118278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-89680739200304159922018-04-06T09:31:33.240+02:002018-04-06T09:31:33.240+02:00Hello Davide, thank for your work. If you measured...Hello Davide, thank for your work. If you measured maximum pulse generating frequency, can you share ?Anonymoushttps://www.blogger.com/profile/16429335650792051324noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-71047831183035950092018-01-29T19:43:02.223+01:002018-01-29T19:43:02.223+01:00Hello, there is no continous spinning mode impleme...Hello, there is no continous spinning mode implemented in this driver, but you can implement it by using something like astepper_getsteptotarget and astepper_moverelative.Davide Gironihttps://www.blogger.com/profile/16366076989473118278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-28620189712080036472018-01-29T17:22:11.706+01:002018-01-29T17:22:11.706+01:00Hello,
Could you please tell which API funcion sho...Hello,<br />Could you please tell which API funcion should I use for "continuous spinning mode"<br /><br />ThanksAnonymoushttps://www.blogger.com/profile/03987259548406402374noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-86342290188344408672017-10-28T10:19:48.819+02:002017-10-28T10:19:48.819+02:00Hello, you have to build your own protocol to driv...Hello, you have to build your own protocol to drive the library.Davide Gironihttps://www.blogger.com/profile/16366076989473118278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-14443943822829790702017-10-27T22:47:11.235+02:002017-10-27T22:47:11.235+02:00Hi...
what are the UART Commands to accelerate th...Hi...<br /><br />what are the UART Commands to accelerate the steppers?<br /><br />TanksAnonymoushttps://www.blogger.com/profile/17690583219970315161noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-35577584503708058482016-01-31T22:57:05.021+01:002016-01-31T22:57:05.021+01:00Okay , I'll work on itOkay , I'll work on itAnonymoushttps://www.blogger.com/profile/14183653614898899278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-44215553397569471982016-01-31T11:59:51.909+01:002016-01-31T11:59:51.909+01:00Hello, I'm sorry but i do not use nor have any...Hello, I'm sorry but i do not use nor have any version of Atmel Studio installed at preset. It should work on Studio too, just try to import all the files, and ask the compiler to compile all of them.Davide Gironihttps://www.blogger.com/profile/16366076989473118278noreply@blogger.comtag:blogger.com,1999:blog-6100511197805579796.post-60677512827439627012016-01-30T18:19:00.508+01:002016-01-30T18:19:00.508+01:00Hello. very good library . Please tell me how to u...Hello. very good library . Please tell me how to use your library in ATMEL Studio6.2.? I understand that it is necessary to convert but do not know how.Anonymoushttps://www.blogger.com/profile/14183653614898899278noreply@blogger.com